Hytera logistics and distribution two way radio communication product solutions
HRS Heat Exchangers - ZLD solves Spanish tannery waste issues

ZLD solves Spanish tannery waste issues

Zero liquid discharge (ZLD) is a waste management technique which transforms liquid waste streams from industrial plants into clean water, which can be reused in the process, and a minimal amount of solid residue, which often include valuable by-products. It is particularly useful for industries producing complex wastes which are difficult to treat using traditional techniques.

One such industry is leather processing and tanning where animal skins are transferred into high quality fabric for use in footwear, upholstery, car interiors and other goods. Based in Salinas near Alicante, Boxcapiel is one of Spain’s leading leather producers, processing skins from a range of species into high quality leather for a wide variety of end uses.

Tightening environmental legislation meant that Boxcapiel’s traditional waste disposal techniques were no longer acceptable or economic. The company urgently needed to find a sustainable and alternative waste treatment. Having been made aware of an existing HRS ZLD system in the locality, Boxcapiel asked HRS Heat Exchangers to investigate the feasibility of such a system at its own plant.

The effective design of any ZLD system is dependent on the correct analysis of the water/waste stream. It is essential to have accurate estimates of composition, flow rates, chemistry, etc. Without this, any designed solution will fail to deliver the required results. The first step was therefore for HRS to commission laboratory studies of the waste stream, followed by the use of a pilot plant to test the proposed solution in situ at Boxcapiel.

Using this information, HRS engineers were then able to design the full ZLD evaporation system, based around the proven, patented HRS Unicus Series of reciprocating scraped surface heat exchangers. Traditionally, vapour compression evaporation has been the main method employed for ZLD processing, with evaporation typically recovering around 95 per cent of wastewater as distillate. Any remaining concentrate is then further treated physically or chemically to produce solid residues (such as crystals) and water. Evaporators used in ZLD systems are often run at lower pressures in order to reduce the boiling point of the liquid being treated.

Working with a reduced boiling point means that multi-effect evaporation is possible. In multi-effect evaporation, steam from the previous evaporation stage is used as the thermal energy in the next stage which works at a lower boiling point. This way, multiple evaporation stages are combined, and energy savings are obtained.

The HRS ZLD system supplied to Boxcapiel begins by using multi-effect evaporation to concentrate the waste stream, resulting in a solution which containing elevated salt levels very close to the saturation point. This is then cooled to promote the formation of salt crystals. Further crystallisation then occurs in specially designed crystallisation tanks, with separation of the crystals that are formed. A supernatant layer of concentrated solution remains after this stage and is returned to the second evaporator for reprocessing.

Both the evaporation and cooling steps result in a high degree of material fouling on the inside of the equipment, so HRS Unicus Series scraped-surface evaporators are used to maintain thermal efficiency and remove fouling as it occurs in the evaporation process. The result is an efficient process which can work continuously without requiring scheduled downtime.

The installed ZLD system produces clean water, which is utilised in the tanning process, and a solid residue, which can be disposed of via normal waste management channels, although Boxcapiel are keen to monetise this potentially valuable material.

The use of the HRS ZLD system has enabled Boxcapiel to meet increasingly stringent environmental regulations, improve the sustainability of its operations, and continue to operate profitability as one of the country’s leading manufacturers of quality leather materials.

More about HRS Heat Exchangers

Located in the UK, HRS Heat Exchangers is part of the HRS Group which operates at the forefront of thermal technology, offering innovative heat transfer solutions worldwide across a diverse range of industries. With 40 years’ experience in the waste sector, specialising in the design and manufacture of an extensive range of turnkey systems and components, incorporating our corrugated tubular and scraped surface heat exchanger technology, HRS units are compliant with global design and industry standards. HRS has a network of offices throughout the world: Australia, New Zealand, UK, Spain, USA, Malaysia and India; with manufacturing plants in the UK, India and Spain.

www.hrs-heatexchangers.com

Check Also

BITO ramps up to meet order growth

BITO ramps up to meet order growth

BITO Storage Systems has taken on additional staff and developed new services to support the …

MHW Latest Top Tweets